Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Tytuł pozycji:

Effect of high-speed steel screw drill geometry on cutting performance when machining austenitic stainless steel.

Tytuł:
Effect of high-speed steel screw drill geometry on cutting performance when machining austenitic stainless steel.
Autorzy:
Sedlak J; Faculty of Mechanical Engineering, Brno University of Technology, Brno, Czech Republic.
Zouhar J; Faculty of Mechanical Engineering, Brno University of Technology, Brno, Czech Republic. .
Kolomy S; Faculty of Mechanical Engineering, Brno University of Technology, Brno, Czech Republic.
Slany M; Faculty of Mechanical Engineering, Brno University of Technology, Brno, Czech Republic.
Necesanek E; NÁSTROJE CZ, s.r.o., Kyjov, Czech Republic.
Źródło:
Scientific reports [Sci Rep] 2023 Jun 07; Vol. 13 (1), pp. 9233. Date of Electronic Publication: 2023 Jun 07.
Typ publikacji:
Journal Article
Język:
English
Imprint Name(s):
Original Publication: London : Nature Publishing Group, copyright 2011-
References:
Materials (Basel). 2022 Mar 07;15(5):. (PMID: 35269212)
Grant Information:
FSI-S-22-7957 Brno University of Technology, Czech Republic
Entry Date(s):
Date Created: 20230607 Date Completed: 20230608 Latest Revision: 20230610
Update Code:
20240105
PubMed Central ID:
PMC10247819
DOI:
10.1038/s41598-023-36448-y
PMID:
37286666
Czasopismo naukowe
Drilling into the solid material is one of the basic technological operations, which creates a cylindrical hole in an appropriate time with required quality. Drilling operation demands a favourable removal of chips from the cutting area because a creation of an undesirable shape of chips can impart a lower quality of the drilled hole corresponding with the generation of excess heat due to the intense contact of the chip with drill. The solution for a proper machining is a suitable modification of the drill geometry i.e., point and clearance angles as presented in current study. The tested drills are made of M35 high-speed steel characterized by a very thin core at the point of the drill. An interesting feature of the drills is the use of cutting speed higher than 30 m min -1 , with the feed of 0.2 mm per revolution. The surface roughness (Ra and Rz lower than 1 µm and 6 µm respectively), cylindricity (0.045 mm), roundness (0.025 mm), perpendicularity of the hole axis (0.025 mm), diameters and position of the individual holes were achieved for a drill with point angle 138.32°and clearance angle 6.92 respectively. The increase of the drill point angle by 6° resulted in the decrease in the feed force of more than 150 N. In addition, an increase of the clearance angle by 1° resulted with a decrease in the feed force of 70 N. The results of the experiment showed that with the correct geometry of the tool the effective machining without using internal cooling can be realised.
(© 2023. The Author(s).)
Zaloguj się, aby uzyskać dostęp do pełnego tekstu.

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies